Your Plumbing Crash Course: A Guide to Installing a Bathtub
Your Plumbing Crash Course: A Guide to Installing a Bathtub
Blog Article
What're your opinions concerning How to Install a Bathtub?

Mounting a bath tub isn't specifically rocket science, but it does call for solid plumbing, carpentry, and in some cases, tiling skills. Changing an old bath tub with a brand-new one is additionally a moderately challenging job. If the old bathtub is readily obtainable, the project can move easily; if you have to open a wall to get rid of the old bathtub and place the new bath tub, the job is a lot harder. In either situation, the job is within a house handyman's skills, although you will certainly need an assistant to vacate the old bathtub and embeded in the new one. Make sure you have certified on your own for the job and are comfortable trying it. As opposed to employing a specialist to take control of a halfway-completed project, it is much better to consider utilizing one prior to you start. Opportunities are you may need a professional plumber to make tube connections.
This post will certainly aid you mount a brand-new bathtub in your bathroom if you have actually currently bought a new bathtub and also don't require to alter the setup of your previous water system pipes.
Your tools and also material checklist must make up the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is disconnect the water supply. After doing so, activate the taps to drain pipes any water remaining in the system. The procedure of getting rid of the existing faucets can be quite bothersome as a result of the restricted access that is typically the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipes to the faucets. Have a cloth prepared for the staying water that will originate from the pipelines. Once the supply pipelines have actually been gotten rid of, make use of the very same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the single taps from transforming during this process. When the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old sealing compound.
Before going on to fit the new taps, contrast the pipeline connections on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the brand-new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end provides a connection to the current supply pipelines.
If you require to fit a monobloc, then you will require decreasing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the faucet in the mounting hole in the bath/basin guaranteeing that the washers are in area in between the faucet as well as the sink. Safeguard the tap in place with the maker supplied backnut. When the faucet is firmly in place, the supply pipes can be linked to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical tap connectors. The former type must be attached to the tap finishes first, tightening only by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Mounting the Bath tub
Making use of the two wooden boards under its feet, position the bathtub in the required setting. The wood boards are practical in evenly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto four little points.
The next goal is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level and changing the feet on the bath tub up until the spirit level checks out degree.
To set up faucets, fit all-time low of the outermost flexible faucet port to the suitable supply pipeline by making a compression join; after that do the exact same for the various other tap.
Switch on the water system and also inspect all joints and also brand-new pipework for leaks and also tighten them if necessary. Fill up the bath tub and also examine the overflow outlet and also the normal outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the supplier's user's manual. Tiling and also securing around the tub should wait until the tub has actually been utilized at the very least when as this will resolve it into its last setting.
Getting ready for the Setup
Firstly, the supporting frame provided with the bathroom needs to be fitted (if required) according to the maker's guidelines. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to make sure that if the faucet comes with a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps system to prevent stress on the bath tub.
Fit the versatile tap adapters to the bottom of the two taps utilizing 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom ought to now prepare to be fitted in its last setting.
Tiling Around the Tub
In the area where the bath satisfies the floor tile, it is needed to seal the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to fracture a rigid seal, causing the water to penetrate the wall surface between the bath as well as the tiling, causing difficulties with dampness and also possible leakages to the ceiling below.
You can choose from a variety of coloured sealers to blend in your components and installations. They are offered in tubes and cartridges, as well as can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched newspaper or soft rope. Remember to always fill up the bathtub with water prior to sealing, to enable the activity experienced when the tub remains in use. The sealant can crack relatively very early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently readily available on the market. It is suggested to fit the floor tiles making use of waterproof or water resistant adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

As a serious person who reads on How to Install a Bathtub, I thought sharing that excerpt was sensible. Sharing is nice. You never know, you may just be doing someone a favor. I am grateful for your time. Kindly come visit our site back soon.
Dial instantly! Report this page